Machine Knit Leg Warmers / Boot Toppers

Tomorrow is New Year’s Day. No commitments, have lots of time of knit, looking forward to doing the first project of the year and the forecast high for Thursday is 10 degrees. It’s a perfect time to whip up a pair of leg warmers. These were knit flat on a Brother KH860 with KR850 ribber using Franklin Sock Yarn from Valley Yarns.

Gauge

Stockinette: 31 stitches x 40 rows = 4″/10cm
Finished Size:
Ankle: 7 1/2″
Cuff: 10 1/2″
Total Length: 14″

Cast On

Disconnect ribber carriage and position it on the left.
Position main carriage with ribber arm on the right.
Set pitch lever to H and rack to position 5.
Set up for industrial rib with edge pairs on the main bed (see note 1): 36L – 35R on the main bed, 35L – 33R on the ribber. Pull one extra ribber needle (35R) to WP to round off the zig-zag row.
Pull ribber needles a little higher than WP and make sure all latches are open. The tips of the ribber needles should be even with the main bed’s gate posts. Main bed needles should be in WP.
Thread the main carriage leaving long tail for seam, set the tension to T0 and RC = 0.
Rack to position 6. Knit from right to left with the main carriage only.
Carefully push the ribber needles back to WP. Make sure the floats that passed over the ribber needles are caught in the needle hooks.
Hang the ribber comb and weights (see note 2).
Connect the ribber carriage and set the carriages to knit circular:  depress the left part button on the main carriage and set the ribber’s right cam lever  to PR.
Set the tension on both carriages to T1. Knit 2 rows, ending COL RC=3.
Transfer the extra ribber stitch on 35R to 34R on the main bed.
Set the tension on both carriages to T2. Knit 1 more row, ending COR RC = 4.

Ribbed Ankle

Set both carriages to knit: release the part button on the main carriage and set the ribber’s right cam lever to N).
Set the tension on both carriages to T5.
Rack to position 5.
Knit 21 rows, ending COL RC = 25.
Transfer the left stitch of each pair of ribber stitches to the corresponding empty main bed needle (see note 3).
Knit 1 row, ending COR RC = 26.
Set pitch lever to P.
Transfer the remaining stitches from the ribber to the corresponding needle on the main bed. There will be two stitches on these needles.

Leg

Drop ribber bed, remove ribber arm and attach normal sinker plate.
Set RC = 0.
Knit 1 row.
* Increase 1 stitch each side.
Knit 4 rows.
Increase 1 stitch each side.
Knit 5 rows. **
Repeat from * to ** 10 more times RC = 100 (58L – 57R).
Increase 1 stitch each side (59L – 58R).
Knit 1 rows RC = 101.

Ribbed Cuff

Set pitch lever to P and rack to position 5.
Transfer pairs of stitches from main bed to ribber for industrial rib 59L – 57R (see note 4). On right hand side, put two stitches on 56R and edge stitch on 57R. On main bed, there will be one stitch every 3rd needle from 57L – 55R.
Transfer heel of each main bed stitch right one needle needle to complete industrial rib setup.
Set pitch lever to H.
Set RC = 0.
Knit 44 rows and bind off.

Finishing

With right side facing, seam ankle rib and leg.
Turn inside out and continue seaming cuff.

Notes

  1. Placing the edge stitches on the main bed means there will be one knit stitch on either side of the ankle seam.
  2. On my Brother, the two beds are close enough that getting the ribber comb and thick industrial rib to hang freely is problematic. I get around that issue by pulling up on the bracket levers and pushing down on the ribber bed to position it slightly lower than normal.
  3. I find that transferring both stitches from the ribber to the main bed at the same time creates a little bump on the inside of the knit that I don’t like. Transferring half the stitches on one row and the other half on a separate row eliminates the bump.
  4. Similar to the ankle rib, placing the edge stitches on the ribber means there will be one knit stitch on either side of the cuff seam. This is a turn-down cuff, so the side facing is the side that will be showing.
Posted in knitting and tagged .

Leave a Reply

Your email address will not be published. Required fields are marked *